everlight electronics co., ltd. http:// www.everlight.com rev 2 page: 1 of 10 device no dtd-152-002 prepared date 02-26-2008 prepared by daniel yang technical data sheet silicon pin photodiode pd15-22b/tr8 features ? fast response time ? high photo sensitivity ? small junction capacitance ? pb free ? the product itself will remain within rohs complian t version. descriptions ? pd15-22b/tr8 is a high speed and high sensitive pin photodiode in miniature flat top view len s smd package and it is molded in a black plast ic. the device is spectrally matched to visible and infrared emitting diode. applications ? high speed photo detector ? copier ? game machine device selection guide chip led part no. material lens color pd15-22b/tr8 silicon black
everlight electronics co., ltd. http:// www.everlight.com rev 2 page: 2 of 10 device no dtd-152-002 prepared date 02-26-2008 prepared by daniel yang 4-r0.25 2.8 2.3 3.3 1.4 2.1 2.3 0.45 1.1 2.0 2.1 1.2 1.4 1.0 0.9 0.9 pd15-22b/tr8 package dimensions notes: 1.all dimensions are in millimeters 2.tolerances unless dimensions 0.1mm absolute maximum ratings (ta=25 ) parameter symbol rating units reverse voltage v r 32 v operating temperature t opr -40 ~ +85 storage temperature t stg -40 ~ +100 soldering temperature *1 t sol 260 power dissipation at(or below) 25 free air temperature p c 150 mw notes: *1:soldering time Q 5 seconds.
everlight electronics co., ltd. http:// www.everlight.com rev 2 page: 3 of 10 device no dtd-152-002 prepared date 02-26-2008 prepared by daniel yang pd15-22b/tr8 electro-optical characteristics (ta=25 ) parameter symbol condition min typ max unit rang of spectral bandwidth 10% of p 730 --- 1100 nm wavelength of peak sensitivity p --- --- 940 --- nm open-circuit voltage v oc ee=5mw /cm 2 p =940nm --- 0.41 --- v short-circuit current i sc ee=1mw /cm 2 p =875nm 4.0 6.5 --- a reverse light current i l ee=1mw /cm 2 p =875nm v r =5v 4.2 6.5 --- a dark reverse current i d ee=0mw /cm 2 v r =10v --- --- 10 na reverse breakdown voltage b vr ee=0mw /cm 2 i r =100 a 32 170 --- v total capacitance c t ee=0mw /cm 2 f=1mhz v r =5v --- 6 --- pf rise time t r --- 10 --- fall time t f v r =5v r l =1000 --- 10 --- ns
everlight electronics co., ltd. http:// www.everlight.com rev 2 page: 4 of 10 device no dtd-152-002 prepared date 02-26-2008 prepared by daniel yang 0 -25 50 100 150 25 0 50 200 75 85 100 1 20 10 100 40 60 v r =10v 80 100 1000 1.0 0.5 0 5 10 20 15 2 1.5 3.0 v r =5v 0 1.0 ta=25 700 750 850 900 950 1050 1100 o c 0.5 800 1000 pd15-22b/tr8 typical electro-optical characteristics curves fig.1 power dissipation vs. fig .2 spectral sensitivity ambient temperature fig.3 dark current vs. fig .4 reverse light current vs. ambient temperature ee
everlight electronics co., ltd. http:// www.everlight.com rev 2 page: 5 of 10 device no dtd-152-002 prepared date 02-26-2008 prepared by daniel yang 10 10 10 1 10 10 -3 -2 2 v r =10v 0 10 -1 10 1 10 10 3 4 10 5 ta=25 c 10 8 4 2 0.1 t 6 1 10 100 f=1mh z v r =5v 2 pd15-22b/tr8 typical electro-optical characteristics curves fig.5 terminal capacitance vs. fig .6 response time vs. reverse voltage load resistance
everlight electronics co., ltd. http:// www.everlight.com rev 2 page: 6 of 10 device no dtd-152-002 prepared date 02-26-2008 prepared by daniel yang pd15-22b/tr8 precautions for use 1. over-current-proof customer must apply resistors for protection , othe rwise slight voltage shift will cause big current change ( burn out will happen ). 2. storage 2.1 do not open moisture proof bag before the produ cts are ready to use. 2.2 before opening the package, the leds should be kept at 30 or less and 90%rh or less. 2.3 the leds should be used within a year. 2.4 after opening the package, the leds should be kept at 30 or less and 70%rh or less. 2.5 the leds should be used within 168 hours (7 da ys) after opening the package. 2.6 if the moisture absorbent material (silica gel) has faded away or the leds have exceeded the storage time, baking treatment should be performed using the following conditions. baking treatment : 60 5 for 24 hours. 3. soldering condition 3.1 pb-free solder temperature profile 3.2 reflow soldering should not be done more than t wo times. 3.3 when soldering, do not put stress on the leds d uring heating. 3.4 after soldering, do not warp the circuit board.
everlight electronics co., ltd. http:// www.everlight.com rev 2 page: 7 of 10 device no dtd-152-002 prepared date 02-26-2008 prepared by daniel yang pd15-22b/tr8 4.soldering iron each terminal is to go to the tip of soldering iro n temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25w. leave two seconds and more intervals, and do soldering of each terminal. be ca reful because the damage of the product is often started at the time of the hand solder. 5.repairing repair should not be done after the leds hav e been soldered. when repairing is unavoidable, a double-head soldering iron should be used (as below figure). it should be confirmed beforehand whether the characteristics of the leds will or will not be damaged by repairing.
everlight electronics co., ltd. http:// www.everlight.com rev 2 page: 8 of 10 device no dtd-152-002 prepared date 02-26-2008 prepared by daniel yang pd15-22b/tr8 reliability test item and condition the reliability of products shall be satisfied with items listed below. confidence level 90% ltpd 10% no. item test conditions test hours/ cycles sample sizes failure judgement criteria ac/re 1 reflow soldering temp. 260 5 10secs 6mins 22pcs 0/1 2 temperature cycle h : +100 15mins 5mins l : -40 15mins 50cycles 22pcs 0/1 3 thermal shock h :+100 5mins 10secs l :-10 5mins 50cycles 22pcs 0/1 4 high temperature life test temp. +100 vr=5v 1000hrs 22pcs 0/1 5 low temperature life test temp. -40 vr=5v 1000hrs 22pcs 0/1 6 dc operating life v r =5v 1000hrs 22pcs 0/1 7 high temperature/ high humidity 85 / 85% r.h 1000hrs 22pcs i l Q l 0.8 l lower specification limit 0/1
everlight electronics co., ltd. http:// www.everlight.com rev 2 page: 9 of 10 device no dtd-152-002 prepared date 02-26-2008 prepared by daniel yang 4.0 2.00.05 4.0 1.75 8.0 2.95 1.550.05 3.50.05 0.23 1.65 3.35 anode cathode 1 2 1 2 . pd15-22b/tr8 package dimensions 1. reel dimensions note: the tolerances unless mentioned is 0.1mm ,unit = mm 2. carrier tape dimensions:(quantity: 2000pcs/reel) note: the tolerances unless mentioned is 0.1mm ,unit = mm
everlight electronics co., ltd. http:// www.everlight.com rev 2 page: 10 of 10 device no dtd-152-002 prepared date 02-26-2008 prepared by daniel yang rohs pd15-22b/tr8 packing procedure aluminum moistue-proof bag label desiccant label label form specification cpn: customer?s production number p/n : production number qty: packing quantity cat: ranks hue: peak wavelength ref: reference lot no: lot number made in taiwan: production place notes 1. above specification may be changed without notice. everlight will reserve authority on material change for above specification. 2. when using this product, please observe the absolut e maximum ratings and the instructions for using outlined in these specification sheets. e verlight assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in th ese specification sheets. 3. these specification sheets include materials protec ted under copyright of everlight corporation. please don?t reproduce or cause anyone to reproduce them without everlight?s consent. everlight electronics co., ltd. tel: 886-2-2267-2000, 2267-9936 office: no 25, lane 76, sec 3, chung yang rd, f ax: 886-2267-6244, 2267-6189, 2267-6306 tucheng, taipei 236, taiwan, r.o.c http:// www.everlight.com pd15 - 22b/tr8
|
